Canon Vixia Hf S10 Camcorder Lcd Screen Replacement Repair Guide

Difficulty

Easy

Steps

6

Time Required

                          15 - 20 minutes            

Sections

1

• LCD Screen
• 6 steps

Flags

3

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackCanon Vixia HF S10

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

What you need

Step 1

              LCD Screen               

• Turn the camcorder upside down and remove the three 3x4 mm Phillips screws securing the black plastic case.

Turn the camcorder upside down and remove the three 3x4 mm Phillips screws securing the black plastic case.

1024

Step 2

• Flip open the LCD screen.
• Remove the three 3x4 mm Phillips screws securing the black panel plastic case.
• From the inner corner in between the panel and the LCD screen, remove the two 2x2.5 mm Phillips screws and the 3x4 mm Phillips screw.

Flip open the LCD screen.

Remove the three 3x4 mm Phillips screws securing the black panel plastic case.

From the inner corner in between the panel and the LCD screen, remove the two 2x2.5 mm Phillips screws and the 3x4 mm Phillips screw.

Step 3

• Using your fingers, remove the black plastic covering. Underneath the covering, you will find a screw hinge.
• Remove the 2x2.5 mm Phillips screw located at the top of the screw hinge.
• Using your fingers, remove the panel from the base of the camcorder.

Using your fingers, remove the black plastic covering. Underneath the covering, you will find a screw hinge.

Remove the 2x2.5 mm Phillips screw located at the top of the screw hinge.

Using your fingers, remove the panel from the base of the camcorder.

Step 4

• Remove the 2x2.5 mm screw from the right side of the plastic case surrounding the LCD screen.
• Flip over the plastic case and remove the 2x2.5 mm screw.
• Remove the two 2x2.5 mm screws from the front plastic case.

Remove the 2x2.5 mm screw from the right side of the plastic case surrounding the LCD screen.

Flip over the plastic case and remove the 2x2.5 mm screw.

Remove the two 2x2.5 mm screws from the front plastic case.

Step 5

• Using a plastic opening tool, pry off the plastic case surrounding the LCD screen.
• Remove the two 1x2.5 mm screws from the motherboard on the back of the LCD screen.
• Gently pull off the motherboard from the LCD screen.
• Be aware of the orange tab when seperating the motherboard from the LCD screen.

Using a plastic opening tool, pry off the plastic case surrounding the LCD screen.

Remove the two 1x2.5 mm screws from the motherboard on the back of the LCD screen.

Gently pull off the motherboard from the LCD screen.

Be aware of the orange tab when seperating the motherboard from the LCD screen.

Step 6

• Using your fingers, remove the LCD screen.

Using your fingers, remove the LCD screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Karina                     

Member since: 03/03/2015

163 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       Sam Houston State, Team 13-1, Blackburne Winter 2015                        

                                                  Member of Sam Houston State, Team 13-1, Blackburne Winter 2015 



                    SHSU-BLACKBURNE-W15S13G1                     


                                            4 Members                     


                                            9 Guides authored                     

John - Sep 19, 2016

Reply

Not enough detail to be really useful. For example,doesn’t mention how to reconnect the ribbon strip. To be fair, no one else says how to be sure it’s connected properly either.

Dominic Oskis - Jan 3, 2020

Reply

The trick to reconnecting the orange ribbon is to bend back the ribbon from its natural position so it sticks out a bit then to put the plastic body almost back in position, leaving the gap open like a partially opened book. The ribbon and socket should be almost aligned. The gap should be just enough to see in and poke about with a small tweezers. I needed a decent light and glasses to carefully align the ribbon into its receptacle. I used a small fine pair of tweezers to push (not grab!) the ribbon into place. Make sure the ribbon is correctly inserted and aligned then carefully gently flip the securing clip with the the tweezer and moving along the clip push it gently to secure the ribbon. Dont push too hard, it wont help! Next carefully manipulate the shell over the main body making sure it is aligned at back of the camera with the screw holes all lined up. Put just a couple of screws in to stabilize the loose shell then pop in the battery to check operation of the screen and buttons.