Difficulty

Moderate

Steps

11

Time Required

                          5 minutes

Sections

3

  • Battery
  • 3 steps
  • Wrist Strap
  • 5 steps
  • Side Panel
  • 3 steps

Flags

0

  • BackCanon Vixia HF R70

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Power off and unplug the device.
  • Position the camera so that the battery is facing you.

Power off and unplug the device.

Position the camera so that the battery is facing you.

1024

Step 2

  • Locate the latch on the bottom edge of the camera.
  • Hold the battery into place and gently push down on the latch towards the lens.

Locate the latch on the bottom edge of the camera.

Hold the battery into place and gently push down on the latch towards the lens.

Step 3

  • While holding down the latch, remove the battery by pulling it out of the device.

While holding down the latch, remove the battery by pulling it out of the device.

Step 4

              Wrist Strap
  • Position the camcorder so that the wrist strap is facing you.
  • Locate the loose end of the strap.

Position the camcorder so that the wrist strap is facing you.

Locate the loose end of the strap.

Step 5

  • Gently pull on the loose end to separate the Velcro.

Gently pull on the loose end to separate the Velcro.

Step 6

  • Locate the “slot” on bottom right corner of the camcorder where the strap loops through.
  • Pull the strap through the loop.

Locate the “slot” on bottom right corner of the camcorder where the strap loops through.

Pull the strap through the loop.

Step 7

  • Pull the strap through the leather cushion.

Pull the strap through the leather cushion.

Step 8

  • Pull the strap through the slot on the left side of the camcorder.

Pull the strap through the slot on the left side of the camcorder.

Step 9

              Side Panel
  • Position the camcorder so that the side panel is facing you.
  • Locate the two 6mm Phillips #00 screws on the side panel.
  • Remove the the screws using a screwdriver with a Phillips #00 head.

Position the camcorder so that the side panel is facing you.

Locate the two 6mm Phillips #00 screws on the side panel.

Remove the the screws using a screwdriver with a Phillips #00 head.

Step 10

  • Turn the camcorder so that the bottom is facing you.
  • Using your screwdriver, locate and remove the four 6mm Phillips #00 screws connecting the side panel to the bottom of the camcorder.

Turn the camcorder so that the bottom is facing you.

Using your screwdriver, locate and remove the four 6mm Phillips #00 screws connecting the side panel to the bottom of the camcorder.

Step 11

  • Gently remove the side panel by pushing it up from the bottom.

Gently remove the side panel by pushing it up from the bottom.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Thomas Rogienski

Member since: 02/28/2017

501 Reputation

                                      5 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       USF Tampa, Team S2-G2, Nance Spring 2017                        

                                                  Member of USF Tampa, Team S2-G2, Nance Spring 2017 



                    USFT-NANCE-S17S2G2                     


                                            4 Members                     


                                            14 Guides authored