Difficulty

Moderate

Steps

16

Time Required

                          15 minutes

Sections

2

  • Outer Shell
  • 9 steps
  • Speaker
  • 7 steps

Flags

0

  • BackCanon Vixia HF R62

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before beginning speaker replacement, power down device and remove from external power supply. If battery is swollen, take appropriate actions.

For step 16, be prepared to solder and desolder components.

What you need

Step 1

              Outer Shell
  • Remove the strap by undoing the Velcro and pulling it through the thread points.
  • Remove the external battery pack by pressing down on the slide release and sliding it out.

Remove the strap by undoing the Velcro and pulling it through the thread points.

Remove the external battery pack by pressing down on the slide release and sliding it out.

1024

Step 2

  • Remove the three 5mm Phillips #000 screws on the bottom of the device.

Remove the three 5mm Phillips #000 screws on the bottom of the device.

Step 3

  • On the side of the device, remove the following Phillips #000 screws:
  • One 3mm screw
  • One 5mm screw

On the side of the device, remove the following Phillips #000 screws:

One 3mm screw

One 5mm screw

Step 4

  • Remove the panel opposite the display by pulling up perpendicular to the side.

Remove the panel opposite the display by pulling up perpendicular to the side.

Step 5

  • Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.

Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.

Step 6

  • Remove the three 4mm Phillips #000 screws shown.
  • There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.

Remove the three 4mm Phillips #000 screws shown.

There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.

Step 7

  • Using tweezers, disconnect this ribbon cable by pulling straight out.

Using tweezers, disconnect this ribbon cable by pulling straight out.

Step 8

  • Repeat step seven (7) for the remaining three wires shown.

Repeat step seven (7) for the remaining three wires shown.

Step 9

  • Grasp the top of the camera and pull straight up to remove the top panel.

Grasp the top of the camera and pull straight up to remove the top panel.

Step 10

              Speaker
  • Grab the top panel and flip it upside down.

Grab the top panel and flip it upside down.

Step 11

  • Remove the 4mm Phillips #000 screw from the front side top panel.

Remove the 4mm Phillips #000 screw from the front side top panel.

Step 12

  • Remove the other two 4mm Phillips #000 screws from the green chip.

Remove the other two 4mm Phillips #000 screws from the green chip.

Step 13

  • Separate the chip from the black plastic part and remove the black plastic part.

Separate the chip from the black plastic part and remove the black plastic part.

Step 14

  • Remove four 4mm Phillips #000 screws on the top of the metal part.

Remove four 4mm Phillips #000 screws on the top of the metal part.

Step 15

  • Take off the electronic component.

Take off the electronic component.

Step 16

  • Lift the speaker and desolder the two wires from the circuit.
  • Check out our How to Solder and Desolder Connections guide for our best soldering practices.

Lift the speaker and desolder the two wires from the circuit.

Check out our How to Solder and Desolder Connections guide for our best soldering practices.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 7 other contributors 


                    Jonathan Francis Eraula

Member since: 10/03/2019

289 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       The Citadel Military College of South Carolina, Team S1-G23, Eggleston Fall 2019                        

                                                  Member of The Citadel Military College of South Carolina, Team S1-G23, Eggleston Fall 2019 



                    CMCSC-EGGLESTON-F19S1G23                     


                                            3 Members                     


                                            8 Guides authored