Difficulty
Easy
Steps
12
Time Required
10 minutes
Sections
2
- Outer Shell
- 9 steps
- Navigation Buttons
- 3 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackCanon Vixia HF R62
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Shell
- Remove the strap by undoing the Velcro and pulling it through the thread points.
- Remove the external battery pack by pressing down on the slide release and sliding it out.
Remove the strap by undoing the Velcro and pulling it through the thread points.
Remove the external battery pack by pressing down on the slide release and sliding it out.
1024
Step 2
- Remove the three 5mm Phillips #000 screws on the bottom of the device.
Remove the three 5mm Phillips #000 screws on the bottom of the device.
Step 3
- On the side of the device, remove the following Phillips #000 screws:
- One 3mm screw
- One 5mm screw
On the side of the device, remove the following Phillips #000 screws:
One 3mm screw
One 5mm screw
Step 4
- Remove the panel opposite the display by pulling up perpendicular to the side.
Remove the panel opposite the display by pulling up perpendicular to the side.
Step 5
- Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.
Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.
Step 6
- Remove the three 4mm Phillips #000 screws shown.
- There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.
Remove the three 4mm Phillips #000 screws shown.
There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.
Step 7
- Using tweezers, disconnect this ribbon cable by pulling straight out.
Using tweezers, disconnect this ribbon cable by pulling straight out.
Step 8
- Repeat step seven (7) for the remaining three wires shown.
Repeat step seven (7) for the remaining three wires shown.
Step 9
- Grasp the top of the camera and pull straight up to remove the top panel.
Grasp the top of the camera and pull straight up to remove the top panel.
Step 10
Navigation Buttons
- Use the Phillips #000 screwdriver to remove three 3mm Phillips #000 screws from the outer casing shell around the record button and remove it and the small microchip.
Use the Phillips #000 screwdriver to remove three 3mm Phillips #000 screws from the outer casing shell around the record button and remove it and the small microchip.
Step 11
- Use the Phillips #000 screwdriver to remove five 3mm Phillips #000 screws from the outer casing shell and remove the metal piece containing the speaker.
Use the Phillips #000 screwdriver to remove five 3mm Phillips #000 screws from the outer casing shell and remove the metal piece containing the speaker.
Step 12
- Remove one 3mm Phillips #000 screw holding the navigation button in. Then use the metal spudger to separate the button from the casing.
Remove one 3mm Phillips #000 screw holding the navigation button in. Then use the metal spudger to separate the button from the casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Christopher Lawrence Morden
Member since: 10/03/2019
97 Reputation
1 Guide authored
Badges:
2
Team
The Citadel Military College of South Carolina, Team S1-G23, Eggleston Fall 2019
Member of The Citadel Military College of South Carolina, Team S1-G23, Eggleston Fall 2019
CMCSC-EGGLESTON-F19S1G23
3 Members
8 Guides authored
