Difficulty
Easy
Steps
15
Time Required
5 - 8 minutes
Sections
2
- Outer Shell
- 9 steps
- Lens
- 6 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackCanon Vixia HF R62
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Shell
- Remove the strap by undoing the Velcro and pulling it through the thread points.
- Remove the external battery pack by pressing down on the slide release and sliding it out.
Remove the strap by undoing the Velcro and pulling it through the thread points.
Remove the external battery pack by pressing down on the slide release and sliding it out.
1024
Step 2
- Remove the three 5mm Phillips #000 screws on the bottom of the device.
Remove the three 5mm Phillips #000 screws on the bottom of the device.
Step 3
- On the side of the device, remove the following Phillips #000 screws:
- One 3mm screw
- One 5mm screw
On the side of the device, remove the following Phillips #000 screws:
One 3mm screw
One 5mm screw
Step 4
- Remove the panel opposite the display by pulling up perpendicular to the side.
Remove the panel opposite the display by pulling up perpendicular to the side.
Step 5
- Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.
Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.
Step 6
- Remove the three 4mm Phillips #000 screws shown.
- There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.
Remove the three 4mm Phillips #000 screws shown.
There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.
Step 7
- Using tweezers, disconnect this ribbon cable by pulling straight out.
Using tweezers, disconnect this ribbon cable by pulling straight out.
Step 8
- Repeat step seven (7) for the remaining three wires shown.
Repeat step seven (7) for the remaining three wires shown.
Step 9
- Grasp the top of the camera and pull straight up to remove the top panel.
Grasp the top of the camera and pull straight up to remove the top panel.
Step 10
Lens
- Remove the 5mm Phillips #000 screw on top of the inner case.
Remove the 5mm Phillips #000 screw on top of the inner case.
Step 11
- Remove the two 5mm Phillips #000 screws near the display panel.
Remove the two 5mm Phillips #000 screws near the display panel.
Step 12
- Disconnect the small bundled cable connector on the side of the lens cover by pulling it straight out.
Disconnect the small bundled cable connector on the side of the lens cover by pulling it straight out.
Step 13
- Remove the lens cover by pulling straight away from the body.
Remove the lens cover by pulling straight away from the body.
Step 14
- Remove the three 6mm Phillips #000 screws shown.
Remove the three 6mm Phillips #000 screws shown.
Step 15
- Remove the lens by pulling straight away from the main body.
- Be aware of the small rubber gasket around the lens as it may come loose.
Remove the lens by pulling straight away from the main body.
Be aware of the small rubber gasket around the lens as it may come loose.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Patrick Bennett
Member since: 09/20/2018
277 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
Central Washington University, Team S1-G3, Pengilly Fall 2018
Member of Central Washington University, Team S1-G3, Pengilly Fall 2018
CWU-PENGILLY-F18S1G3
3 Members
10 Guides authored
