Difficulty

Moderate

Steps

23

Time Required

                          9 - 10 minutes

Sections

4

  • Outer Shell
  • 9 steps
  • Lens
  • 6 steps
  • Internal Battery and SD Card Reader
  • 4 steps
  • Central Capturing Unit
  • 4 steps

Flags

0

  • BackCanon Vixia HF R62

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Shell
  • Remove the strap by undoing the Velcro and pulling it through the thread points.
  • Remove the external battery pack by pressing down on the slide release and sliding it out.

Remove the strap by undoing the Velcro and pulling it through the thread points.

Remove the external battery pack by pressing down on the slide release and sliding it out.

1024

Step 2

  • Remove the three 5mm Phillips #000 screws on the bottom of the device.

Remove the three 5mm Phillips #000 screws on the bottom of the device.

Step 3

  • On the side of the device, remove the following Phillips #000 screws:
  • One 3mm screw
  • One 5mm screw

On the side of the device, remove the following Phillips #000 screws:

One 3mm screw

One 5mm screw

Step 4

  • Remove the panel opposite the display by pulling up perpendicular to the side.

Remove the panel opposite the display by pulling up perpendicular to the side.

Step 5

  • Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.

Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel.

Step 6

  • Remove the three 4mm Phillips #000 screws shown.
  • There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.

Remove the three 4mm Phillips #000 screws shown.

There will be foam covers protecting some or all of these screws. These will need to be removed before you will be able to unscrew them.

Step 7

  • Using tweezers, disconnect this ribbon cable by pulling straight out.

Using tweezers, disconnect this ribbon cable by pulling straight out.

Step 8

  • Repeat step seven (7) for the remaining three wires shown.

Repeat step seven (7) for the remaining three wires shown.

Step 9

  • Grasp the top of the camera and pull straight up to remove the top panel.

Grasp the top of the camera and pull straight up to remove the top panel.

Step 10

              Lens
  • Remove the 5mm Phillips #000 screw on top of the inner case.

Remove the 5mm Phillips #000 screw on top of the inner case.

Step 11

  • Remove the two 5mm Phillips #000 screws near the display panel.

Remove the two 5mm Phillips #000 screws near the display panel.

Step 12

  • Disconnect the small bundled cable connector on the side of the lens cover by pulling it straight out.

Disconnect the small bundled cable connector on the side of the lens cover by pulling it straight out.

Step 13

  • Remove the lens cover by pulling straight away from the body.

Remove the lens cover by pulling straight away from the body.

Step 14

  • Remove the three 6mm Phillips #000 screws shown.

Remove the three 6mm Phillips #000 screws shown.

Step 15

  • Remove the lens by pulling straight away from the main body.
  • Be aware of the small rubber gasket around the lens as it may come loose.

Remove the lens by pulling straight away from the main body.

Be aware of the small rubber gasket around the lens as it may come loose.

Step 16

              Internal Battery and SD Card Reader
  • Remove the two 3mm Phillips #000 screws.
  • Remove the 4mm Phillips #000 screw.

Remove the two 3mm Phillips #000 screws.

Remove the 4mm Phillips #000 screw.

Step 17

  • Disconnect the ribbon cable shown.

Disconnect the ribbon cable shown.

Step 18

  • Remove the 4mm Phillips #000 screw at the bottom of the camera.

Remove the 4mm Phillips #000 screw at the bottom of the camera.

Step 19

  • Place the spudger under the tab shown.
  • While prying the tab up with the spudger, pull the case away.

Place the spudger under the tab shown.

While prying the tab up with the spudger, pull the case away.

Step 20

              Central Capturing Unit
  • Using a spudger, disconnect the ribbon cable connector from the PC board shown in the picture.

Using a spudger, disconnect the ribbon cable connector from the PC board shown in the picture.

Step 21

  • Using tweezers, disconnect the ribbon cable shown in the picture by pulling straight out.

Using tweezers, disconnect the ribbon cable shown in the picture by pulling straight out.

Step 22

  • Using a spudger, gently pry up the top tab on the ZIF connector. The wire will now disconnect with no force needed.
  • When reassembling you will need to place the ribbon wire tightly against the tab in order to properly secure it.

Using a spudger, gently pry up the top tab on the ZIF connector. The wire will now disconnect with no force needed.

When reassembling you will need to place the ribbon wire tightly against the tab in order to properly secure it.

Step 23

  • Using your fingers, firmly grasp both ends of the capturing device and gently pull the assembly straight out.

Using your fingers, firmly grasp both ends of the capturing device and gently pull the assembly straight out.

To reassemble the central capturing unit, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Jeffrey Harn

Member since: 09/20/2018

327 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Central Washington University, Team S1-G3, Pengilly Fall 2018                        

                                                  Member of Central Washington University, Team S1-G3, Pengilly Fall 2018 



                    CWU-PENGILLY-F18S1G3                     


                                            3 Members                     


                                            10 Guides authored