Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
5
- Handstrap
- 2 steps
- Battery
- 1 step
- Casing
- 3 steps
- Speaker
- 4 steps
- Power Button
- 1 step
Flags
0
BackCanon Vixia HF R600
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Handstrap
- Pull up the Velcro strap starting from the front of the camera and working your way towards the back.
- If you are adjusting the hand-strap, tighten or loosen the Velcro strap accordingly and reattach it.
- To remove the hand-strap, pull the Velcro strip through the leather pad.
Pull up the Velcro strap starting from the front of the camera and working your way towards the back.
If you are adjusting the hand-strap, tighten or loosen the Velcro strap accordingly and reattach it.
To remove the hand-strap, pull the Velcro strip through the leather pad.
1024
Step 2
- Remove the strap from the camera body.
Remove the strap from the camera body.
Step 3
Battery
- Press in the battery release tab located on the bottom of the camera.
- Slide the battery out from the body.
Press in the battery release tab located on the bottom of the camera.
Slide the battery out from the body.
Step 4
Casing
- Start by removing the two 6mm Phillips #00 screws located on the right side of the camera.
- Remove four more 6mm Phillips #00 screws found on the bottom of the camera.
Start by removing the two 6mm Phillips #00 screws located on the right side of the camera.
Remove four more 6mm Phillips #00 screws found on the bottom of the camera.
Step 5
- Open the display screen and remove the three 5mm Phillips #00 screws.
- Look to the swivel point for the screen to find the last two 5mm Phillips #00 screws that must be removed.
Open the display screen and remove the three 5mm Phillips #00 screws.
Look to the swivel point for the screen to find the last two 5mm Phillips #00 screws that must be removed.
Step 6
- Gently pull the plastic casing away from the camera.
Gently pull the plastic casing away from the camera.
Step 7
Speaker
- Remove one 4mm Phillips JIS#00 screw on the right side of the camera.
- Use the plastic opening tool to undo the bronze ribbon connector.
Remove one 4mm Phillips JIS#00 screw on the right side of the camera.
Use the plastic opening tool to undo the bronze ribbon connector.
Step 8
- Remove one 4mm Phillips JIS#00 screw located on the top of the camera near the battery connection.
- Pull the plastic casing away from the camera. The speaker and power button are housed in this casing.
Remove one 4mm Phillips JIS#00 screw located on the top of the camera near the battery connection.
Pull the plastic casing away from the camera. The speaker and power button are housed in this casing.
Step 9
- Remove four 5mm Phillips PH#00 screws holding the speaker bracket in place.
- Remove one more 5mm screw below the power button.
Remove four 5mm Phillips PH#00 screws holding the speaker bracket in place.
Remove one more 5mm screw below the power button.
Step 10
- Carefully pull the speaker out of the casing.
Carefully pull the speaker out of the casing.
Step 11
Power Button
- Using a pair of tweezers, gently push in the red tabs of the power button.
- Pull the power button out of the camera casing.
Using a pair of tweezers, gently push in the red tabs of the power button.
Pull the power button out of the camera casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Brian Luna
Member since: 02/10/2016
483 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
USF Tampa, Team 14-4, Lacy Spring 2016
Member of USF Tampa, Team 14-4, Lacy Spring 2016
USFT-LACY-S16S14G4
3 Members
16 Guides authored
