Difficulty
Moderate
Steps
9
Time Required
10 minutes
Sections
4
- Handstrap
- 2 steps
- Battery
- 1 step
- Casing
- 3 steps
- Microphone
- 3 steps
Flags
0
BackCanon Vixia HF R600
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Handstrap
- Pull up the Velcro strap starting from the front of the camera and working your way towards the back.
- If you are adjusting the hand-strap, tighten or loosen the Velcro strap accordingly and reattach it.
- To remove the hand-strap, pull the Velcro strip through the leather pad.
Pull up the Velcro strap starting from the front of the camera and working your way towards the back.
If you are adjusting the hand-strap, tighten or loosen the Velcro strap accordingly and reattach it.
To remove the hand-strap, pull the Velcro strip through the leather pad.
1024
Step 2
- Remove the strap from the camera body.
Remove the strap from the camera body.
Step 3
Battery
- Press in the battery release tab located on the bottom of the camera.
- Slide the battery out from the body.
Press in the battery release tab located on the bottom of the camera.
Slide the battery out from the body.
Step 4
Casing
- Start by removing the two 6mm Phillips #00 screws located on the right side of the camera.
- Remove four more 6mm Phillips #00 screws found on the bottom of the camera.
Start by removing the two 6mm Phillips #00 screws located on the right side of the camera.
Remove four more 6mm Phillips #00 screws found on the bottom of the camera.
Step 5
- Open the display screen and remove the three 5mm Phillips #00 screws.
- Look to the swivel point for the screen to find the last two 5mm Phillips #00 screws that must be removed.
Open the display screen and remove the three 5mm Phillips #00 screws.
Look to the swivel point for the screen to find the last two 5mm Phillips #00 screws that must be removed.
Step 6
- Gently pull the plastic casing away from the camera.
Gently pull the plastic casing away from the camera.
Step 7
Microphone
- Remove one 5mm Phillips PH#00 screw from the top of the camera.
- Pull away the plastic shutter casing; this contains the microphone.
- Using the plastic opening tool or something similar, carefully disconnect the white 4 pin connector to remove the shutter casing.
Remove one 5mm Phillips PH#00 screw from the top of the camera.
Pull away the plastic shutter casing; this contains the microphone.
Using the plastic opening tool or something similar, carefully disconnect the white 4 pin connector to remove the shutter casing.
Step 8
- Remove the one 4mm Phillips JIS#00 screw from the top of the shutter housing.
- Pull the shutter away to reveal the metal plate covering the speakers.
Remove the one 4mm Phillips JIS#00 screw from the top of the shutter housing.
Pull the shutter away to reveal the metal plate covering the speakers.
Step 9
- Remove the one 4mm Phillips JIS#00 from the plastic shutter housing.
- Pull the metal bracket out of the housing.
- Carefully remove the speakers from the housing as they contain very thin wires.
Remove the one 4mm Phillips JIS#00 from the plastic shutter housing.
Pull the metal bracket out of the housing.
Carefully remove the speakers from the housing as they contain very thin wires.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Brian Luna
Member since: 02/10/2016
483 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
USF Tampa, Team 14-4, Lacy Spring 2016
Member of USF Tampa, Team 14-4, Lacy Spring 2016
USFT-LACY-S16S14G4
3 Members
16 Guides authored
