Difficulty
Moderate
Steps
13
Time Required
5 - 10 minutes
Sections
3
- Battery
- 3 steps
- Power and Shutter Buttons
- 5 steps
- Display Screen
- 5 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackCanon PowerShot SX600 HS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- To remove the battery, locate the battery cover on the bottom of the camera.
- Using your thumb, press down on the cover and slide it outwards.
To remove the battery, locate the battery cover on the bottom of the camera.
Using your thumb, press down on the cover and slide it outwards.
1024
Step 2
- Depress the orange lever holding the battery in place to unlock it.
Depress the orange lever holding the battery in place to unlock it.
Step 3
- Use your fingers to remove the battery.
- Be sure to remember the alignment of the nodes for reassembly.
Use your fingers to remove the battery.
Be sure to remember the alignment of the nodes for reassembly.
Step 4
Power and Shutter Buttons
- Use a #000 Phillips screwdriver to unscrew the four 4mm screws located on the sides of the camera (2 for each side).
Use a #000 Phillips screwdriver to unscrew the four 4mm screws located on the sides of the camera (2 for each side).
Step 5
- Unscrew the four 2mm located on the bottom of the camera using a Phillips #000 screwdriver.
Unscrew the four 2mm located on the bottom of the camera using a Phillips #000 screwdriver.
Step 6
- Use a plastic opening tool to loosen and remove both the front and back plates of the camera, as well as the two side pieces.
Use a plastic opening tool to loosen and remove both the front and back plates of the camera, as well as the two side pieces.
Step 7
- Unscrew the three 2mm screws attaching the piece to the camera frame with a #000 Phillips screwdriver.
Unscrew the three 2mm screws attaching the piece to the camera frame with a #000 Phillips screwdriver.
Step 8
- Use an opening tool to gently remove the power and shutter button assembly from the frame.
Use an opening tool to gently remove the power and shutter button assembly from the frame.
Step 9
Display Screen
- Unscrew the 2mm screw connections of the main board protector from the camera frame using a #000 Phillips head screwdriver (2 on front, 1 on top)
Unscrew the 2mm screw connections of the main board protector from the camera frame using a #000 Phillips head screwdriver (2 on front, 1 on top)
Step 10
- Use a Phillips #000 screwdriver to unscrew the 4mm screw.
Use a Phillips #000 screwdriver to unscrew the 4mm screw.
Step 11
- Use a pair of tweezers to remove the no-fuss connector from its holder.
Use a pair of tweezers to remove the no-fuss connector from its holder.
Step 12
- Gently lift the protector from the frame.
Gently lift the protector from the frame.
Step 13
- Lift the LCD screen ZIF connector tab and remove the ribbon cable.
- Detach the no-fuss connector.
- Lift the screen from its holder.
Lift the LCD screen ZIF connector tab and remove the ribbon cable.
Detach the no-fuss connector.
Lift the screen from its holder.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
7 other people completed this guide.
Author
with 2 other contributors
Jennyfer Munoz
Member since: 02/15/2017
411 Reputation
3 Guides authored
Badges:
16
+13 more badges
Team
USF Tampa, Team S6-G4, Lacy Spring 2017
Member of USF Tampa, Team S6-G4, Lacy Spring 2017
USFT-LACY-S17S6G4
3 Members
9 Guides authored
Gihan - Oct 30, 2017
Reply
Plz I want othe
Bill Graham - Nov 13, 2019
Reply
I did all this with a new LCD. After reassemble the lens has extended out but camera does not turn on. Should I take it apart again and start from beginning. Is there a connector not in place correctly that will cause this to happen?
