Canon Powershot Sx530 Hs Internal Metal Frame Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Battery
2 steps
Canon PowerShot SX530 HS Back Panel Assembly
4 steps
Internal Button Sensor Plate
2 steps
LCD Display
2 steps
Shutter Back Cover
2 steps
Internal Metal Frame
2 steps

Flags

BackCanon PowerShot SX530 HS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Flip the camera upside down to find the battery compartment (marked CARD/ BATT. OPEN).
Press into the grooves of the battery door and slide the panel in the direction of the arrow.

Flip the camera upside down to find the battery compartment (marked CARD/ BATT. OPEN).

Press into the grooves of the battery door and slide the panel in the direction of the arrow.

1024

Step 2

Gently press down on the orange release button found inside.
After pressing the release button, pull the battery out of the camera.

Gently press down on the orange release button found inside.

After pressing the release button, pull the battery out of the camera.

Step 3

              Canon PowerShot SX530 HS Back Panel Assembly

Flip over the camera.
Use a Phillips PH000 to remove the two 4mm screws near the center of the camera.
Use a Phillips PH000 to remove the two 6mm screws on the ends of the camera.

Flip over the camera.

Use a Phillips PH000 to remove the two 4mm screws near the center of the camera.

Use a Phillips PH000 to remove the two 6mm screws on the ends of the camera.

Step 4

Locate the left side of the camera.
Use a Philips PH000 to remove the two 6mm screws.

Locate the left side of the camera.

Use a Philips PH000 to remove the two 6mm screws.

Step 5

Rotate the camera to the side with the removable cover containing the HDMI and mini USB ports.
Use the Phillips PH000 to remove the 7mm screw located next to the HDMI port. This screw has red loctite.
Use the Phillips PH000 to remove the 4mm screw near the USB port.
Use the Phillips PH000 to remove the 7.4mm screw near the USB port.

Rotate the camera to the side with the removable cover containing the HDMI and mini USB ports.

Use the Phillips PH000 to remove the 7mm screw located next to the HDMI port. This screw has red loctite.

Use the Phillips PH000 to remove the 4mm screw near the USB port.

Use the Phillips PH000 to remove the 7.4mm screw near the USB port.

Step 6

Rotate the camera to locate the side with the LCD screen.
Use a Phillips PH000 to remove the two 6mm screws above the LCD screen.
Once the screws are out the back panel, it is ready to be taken off. Grip the backside of the camera and pull it away evenly on every side. The backside must come off straight from the front.

Rotate the camera to locate the side with the LCD screen.

Use a Phillips PH000 to remove the two 6mm screws above the LCD screen.

Once the screws are out the back panel, it is ready to be taken off. Grip the backside of the camera and pull it away evenly on every side. The backside must come off straight from the front.

Step 7

              Internal Button Sensor Plate

Locate the Internal Button Sensor Plate. This is the white and silver plate to the right of the LCD Display.
Use a Phillips PH000 to remove the two 3mm screws on the panel.
Use a Phillips PH000 to remove the 3mm screw connected to the motherboard.

Locate the Internal Button Sensor Plate. This is the white and silver plate to the right of the LCD Display.

Use a Phillips PH000 to remove the two 3mm screws on the panel.

Use a Phillips PH000 to remove the 3mm screw connected to the motherboard.

Step 8

Peel off the plate. Be careful, as the plate is connected to the motherboard underneath by a ribbon.
Use a plastic opening tool to unlock the ribbon tape.
Remove the ribbon tape from the motherboard.

Peel off the plate. Be careful, as the plate is connected to the motherboard underneath by a ribbon.

Use a plastic opening tool to unlock the ribbon tape.

Remove the ribbon tape from the motherboard.

Step 9

              LCD Display

Locate the Display screen in the center of the camera.
Use a plastic opening tool to pry off the LCD screen. Start on the bottom left corner—this is the furthest away from the ribbon holding it down on the right side.
The adhesive holding down the display should be strong enough to put the display back on.

Locate the Display screen in the center of the camera.

Use a plastic opening tool to pry off the LCD screen. Start on the bottom left corner—this is the furthest away from the ribbon holding it down on the right side.

The adhesive holding down the display should be strong enough to put the display back on.

Step 10

Use a plastic opening tool to unlock the ribbon tape.
Remove the ribbon tape from the motherboard.

Step 11

              Shutter Back Cover

Remove the two screws (5-6mm) on the left and right side of the shutter panel with a Phillips PH000 screwdriver.

Remove the two screws (5-6mm) on the left and right side of the shutter panel with a Phillips PH000 screwdriver.

Step 12

Lift the shutter light and pull the shutter back panel off the camera.
Be careful when pulling out the panel because it is connected to the motherboard.

Lift the shutter light and pull the shutter back panel off the camera.

Be careful when pulling out the panel because it is connected to the motherboard.

Step 13

              Internal Metal Frame

Use a PH000 screwdriver to remove the four 3.5 mm screws holding the plate in place.
Use a PH000 screwdriver to remove the two 2.5 mm screws holding the top of the plate.
Use a PH000 screwdriver to remove the two 4.5 mm screws connecting the plate to the motherboard.

Use a PH000 screwdriver to remove the four 3.5 mm screws holding the plate in place.

Use a PH000 screwdriver to remove the two 2.5 mm screws holding the top of the plate.

Use a PH000 screwdriver to remove the two 4.5 mm screws connecting the plate to the motherboard.

Step 14

Gently pull the plate up and away from the camera.
Part of the plate extends inside the camera beneath the shutter, so be sure to not angle the plate as you pull.

Gently pull the plate up and away from the camera.

Part of the plate extends inside the camera beneath the shutter, so be sure to not angle the plate as you pull.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Joel groff

Member since: 02/02/2017

321 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 16-4, Blackwell Spring 2017                        

                                                  Member of USF Tampa, Team 16-4, Blackwell Spring 2017 



                    USFT-BLACKWELL-S17S16G4                     


                                            4 Members                     


                                            9 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team