Difficulty
Difficult
Steps
11
Time Required
15 - 20 minutes
Sections
5
- Battery
- 2 steps
- Back Face
- 4 steps
- LCD Screen
- 2 steps
- Metal Plate
- 1 step
- Lens
- 2 steps
Flags
1
Missed a Step
Oops! This guide is currently missing some important steps.
BackCanon PowerShot SX520 HS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Using your fingers, slide the battery compartment door to the right until it unlocks.
Using your fingers, slide the battery compartment door to the right until it unlocks.
1024
Step 2
- Rotate the door along hinges to open.
- Take out the battery with your fingers.
Rotate the door along hinges to open.
Take out the battery with your fingers.
Step 3
Back Face
- Remove 2-3.4 mm screws that secure the back panel using a Phillips #000 screwdriver.
- Remove 4-4 mm screws on the left and right sides of the camera using a Phillips #000 screwdriver.
Remove 2-3.4 mm screws that secure the back panel using a Phillips #000 screwdriver.
Remove 4-4 mm screws on the left and right sides of the camera using a Phillips #000 screwdriver.
Step 4
- Remove 2-4 mm screws that secure the bottom of the camera using a Phillips #000 screwdriver.
Remove 2-4 mm screws that secure the bottom of the camera using a Phillips #000 screwdriver.
Step 5
- Pull back the rubber facing to access the A/V and HDMI output compartment.
- Remove 1-3.4mm screw inside the compartment using a Phillips #000 screwdriver.
Pull back the rubber facing to access the A/V and HDMI output compartment.
Remove 1-3.4mm screw inside the compartment using a Phillips #000 screwdriver.
Step 6
- Once all screws are removed, pull the back facing off with your fingers.
Once all screws are removed, pull the back facing off with your fingers.
Step 7
LCD Screen
- Remove 3-4.4 mm screws that secure the small metal plate using a Phillips #000 screwdriver.
Remove 3-4.4 mm screws that secure the small metal plate using a Phillips #000 screwdriver.
Step 8
- Carefully pop out the LCD screen with your fingers.
Carefully pop out the LCD screen with your fingers.
Step 9
Metal Plate
- Remove 6-4.4 mm screws that secure the metal cover using a Phillips #000 screwdriver.
- Remove 2-2.5 mm screws that secure the back panel using a Phillips #000 screwdriver.
- After all 8 screws are removed, pull the metal plate out with your fingers.
Remove 6-4.4 mm screws that secure the metal cover using a Phillips #000 screwdriver.
Remove 2-2.5 mm screws that secure the back panel using a Phillips #000 screwdriver.
After all 8 screws are removed, pull the metal plate out with your fingers.
Step 10
Lens
- Unlcip the large cable by pulling up on the metal part with your finger.
- Slide out the 2 smaller cables with your fingers.
Unlcip the large cable by pulling up on the metal part with your finger.
Slide out the 2 smaller cables with your fingers.
Step 11
- Lift up the lens by grabbing the sides with your fingers.
Lift up the lens by grabbing the sides with your fingers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 5 other contributors
Lisa Choe
Member since: 09/22/2015
460 Reputation
3 Guides authored
Badges:
12
+9 more badges
Team
Baylor, Team 4-4, Williams Fall 2015
Member of Baylor, Team 4-4, Williams Fall 2015
BU-WILLIAMS-F15S4G4
4 Members
6 Guides authored
