Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

1

  • LCD Screen
  • 9 steps

Flags

0

  • BackCanon PowerShot SX260 HS

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              LCD Screen
  • Be sure to always remove the battery from the camera before disassembling to avoid permanent damage.
  • The camera has a total of 6 (3 mm) external screws that will need to be removed; 2 on the left side, 2 on the bottom, and 2 on the right side.
  • Remove the 2 (3 mm) screws on the left side
  • Remove the 2 (3 mm) screws on the bottom of the camera.
  • Remove the 2 (3 mm) screws on the right side of the camera.

Be sure to always remove the battery from the camera before disassembling to avoid permanent damage.

The camera has a total of 6 (3 mm) external screws that will need to be removed; 2 on the left side, 2 on the bottom, and 2 on the right side.

Remove the 2 (3 mm) screws on the left side

Remove the 2 (3 mm) screws on the bottom of the camera.

Remove the 2 (3 mm) screws on the right side of the camera.

1024

Step 2

  • Use your plastic opening tool to gently lift and remove back face plate.
  • Unplug the ribbon cable leading to the mode dial.

Use your plastic opening tool to gently lift and remove back face plate.

Unplug the ribbon cable leading to the mode dial.

Step 3

  • After removing exterior screws, gently lift off the front face plate with your fingers.

After removing exterior screws, gently lift off the front face plate with your fingers.

Step 4

  • Remove the 4 (3 mm) screws that are under the face plate.

Remove the 4 (3 mm) screws that are under the face plate.

Step 5

  • Next, remove the 2 (3 mm) interior screws on the left side of the camera.

Next, remove the 2 (3 mm) interior screws on the left side of the camera.

Step 6

  • After removing the interior left screws, use a plastic opening tool to gently pull the top face plate off.

After removing the interior left screws, use a plastic opening tool to gently pull the top face plate off.

Step 7

  • Next,take off the 2 (3mm) screws on the back side of the camera to remove the dial panel.
  • Gently lift the panel with your fingers.
  • Be careful not to rip the attached yellow ribbon cable.

Next,take off the 2 (3mm) screws on the back side of the camera to remove the dial panel.

Gently lift the panel with your fingers.

Be careful not to rip the attached yellow ribbon cable.

Step 8

  • Carefully unplug the yellow ribbon cable from the front of the camera using your tweezers.

Carefully unplug the yellow ribbon cable from the front of the camera using your tweezers.

Step 9

  • Gently slide the LCD screen to the right and remove.

Gently slide the LCD screen to the right and remove.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors 


                    Tyler Kelch

Member since: 03/05/2015

595 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Sam Houston State, Team 11-8, Blackburne Winter 2015                        

                                                  Member of Sam Houston State, Team 11-8, Blackburne Winter 2015 



                    SHSU-BLACKBURNE-W15S11G8                     


                                            2 Members                     


                                            4 Guides authored